Children's Educational Toys Adult Design-Work 130-230 Degree High Temperature 3D Printing Pen

Product Description

Product and Model:
Children's Educational Toys Adult Design-Work 130-230 Degree High Temperature 3d Printing Pen (XH-PP-800)

Specs:
1) LED display can directly show the temperature, materials used
2) Use the material: PLA, ABS
3) Support dual-mode for feeding: hold the "Forward" button to feed continuously and release to stop feeding, or double press the "Forward" button to feed continuously and press again to stop feeding
4) Long press "Return" button for 2 seconds to return the supplies automatically
5) Printing temperature: 130~230°C
6) The material of the pen tip: aviation pottery material, high temperature resistant and non clogging nozzle
7) Working conditions: 10~35°C
8) Applicable age: over 12 years old
9) Product size: 180*45*38mm, weight 140g
10)Product color: yellow, blue, purple, white
11)Packing: 40pcs/ctn, ctn size 53*42.5*37cm, G.W. 17kg
 
Warnings!
1. This equipment is suitable for children over 8 years old and adult. It can be used by children under the guardianship of adults.
2. Front near the tip and the device for high temperature danger zone, so it is forbidden to touch or use the pen point touch other items.
3. It is prohibited to insert  foreign body into the entry hole. 
4. The equipment is precision electronic instruments, keep it away from water and other liquids.
5. Please put it in a safe place, to prevent falling from high altitude or away for children's touch.

Packing List
1 × 3D pen
1 × Power adapter
1 × Pen cap
1 × User Manual
1 × Material PCL

Operating instructions:
1. Connect the power adapter with power source, and the other end into the 3D pen. If the Red LED lights on, the LED screen displays "PLA" , it means the equipment has entered the standby state.
2. The LED screen displays "PLA" or "ABS", selecting the supplies by pressing the "Temperature control switch/Material selection" button. To avoid malfunction, the selection must be same as the supplies attribute.
3. Press "Forward" button, the red LED light change to yellow, which indicates that the equipment has entered into warm-up state. When the red LED lights changes to blue. It means the warm-up process is finished and the equipment can operate normally.
4. Insert the supplies into the "supplies introduction hole", then press "Foward" button, supplies will be conveyed by the built-in motor of the equipment. When the glue is spit out  from the integrated nozzle heating head, it means the 3D pen is installed successfully.
5. Recommended operating temperature for PLA and ABS: PLA(185-210ºC), ABS(210-230ºC). Different colors of homogeneous supplies have different melting points, please tune the temperature according to the yielding situation. (Please refer to " temperature tuning" part for the melting point and temperature adjustment of the supplies)
6. The device will enter into sleeping mode automatically and the LED screen will display "SLEEP" when the device is not used more than 3 minutes. If you need to use it again, press "Forward" button to trigger it.
7. If you need to change supplies, please press "Return" for 2 seconds and then repeat step 4.

Note
Heating time is influenced by preset temperature and  environmental temperature. 
Remember to uninstall the supplies after use.

Temperature Tuning
Due to the different melting points for different color supplies, in order to improve the quality of creation, please pay attention to the following questions:
In low speed working mode, if you hear "crackling" sound from the nozzle end, it means the temperature is too high, press"Temperature control switch "button to turn the temperature down, the adjustment range should be 5-10ºC. In normal working mode, if encounter lots of bubbles, showed that the temperature is too high, press the "Temperature control switch" button to turn the temperature down, the adjustment range should be 3-8ºC. If the surface color of extrusion glue become dim and dark, sounds of the motor become obviously difficulty, it means the temperature is too low, use the temperature control switch button to raise the temperature, the adjustment range should be 5-10ºC. Normal spiting should be smooth without bubbles. (occasionally bubbles)

Product Show:

Lead Time:

Sample	2 days
100  pcs	6 days
500  pcs	8 days
1000 pcs	10days
5000 pcs	20days
10000pcs	30days

Shipping Way:
By DHL/UPS/FedEx and by Air for small quantity orders, by Sea for big orders.